Swing Gate Repair Houston TX — Hinges, Posts & Operators
Rampart Welding repairs swing gates across Houston — sagging gates, worn greaseable ball-bearing barrel hinges, leaning posts, and swing operators like the LA400 and LA500. Because we weld in-house, we fix the structural cause of the sag, not just adjust the opener. Call (713) 816-5880.
A swing gate that sags, drags, or won't latch has a structural problem — a worn hinge or a shifted post — that no opener adjustment will fix. We weld in new heavy-duty hinges, reset posts, and re-square the gate, then tune the operator.
Swing Gate Problems We Fix
Structural and operator faults.
- Gate sagging at the latch end
- Worn or seized barrel hinges
- Leaning or shifted hinge post
- Gate won't latch or align
- Swing operator stalling (Code 93)
- Dual swing gates out of sync
Why Is My Swing Gate Sagging?
A sagging swing gate almost always has a worn hinge or a shifted hinge post. As the greaseable ball-bearing barrel hinge wears or the post leans in Houston's clay, the latch end drops, the gate drags, and the latch stops catching. We weld in a new hinge and re-plumb the post.
Sag is gravity exposing a structural weakness. The fix isn't shimming the latch or adjusting the operator — it's addressing the hinge and post that are actually letting the gate drop. Because we weld in-house, we install a heavy-duty hinge and reset the post permanently rather than applying a temporary patch.
- Hinge wear inspected — pin, barrel, and bearing
- New heavy-duty greaseable hinge welded in
- Hinge post plumb checked and reset if shifted
- Gate re-squared and latch realigned
What Goes Wrong With Swing Gates in Houston?
Worn Barrel Hinges
Greaseable ball-bearing barrel hinges carry the gate's full weight and wear out — especially when never greased. A worn hinge lets the gate sag and bind. We replace it with a heavy-duty welded hinge.
Shifted Hinge Posts
Houston clay heaves the hinge post out of plumb, tilting the whole gate. We reset the post with a proper footing so the gate swings level and the operator stops fighting the misalignment.
Operator Stalls
Swing operators like the LA400 and LA500 throw Code 93 when a sagging gate forces them past their load. We fix the structure first, then recalibrate the operator and limits.
My Dual Swing Gates Don't Meet in the Middle — Why?
Misaligned dual swing gates usually have one leaf sagging from a worn hinge or shifted post, or the two operators out of sync on their timing and limits. We level both leaves structurally first, then resynchronize the operators so they meet cleanly.
Dual gates have to move in coordinated timing and meet precisely in the center. When they stop meeting, it's either structural — one leaf has dropped — or electronic — the operators have drifted out of sync. We address both, in that order, so the gates close flush again.
- Both leaves checked for sag and structural level
- Hinges and posts repaired as needed
- Operator timing and limits resynchronized
- Center meeting point verified through full cycles
Diagnostic & Service Pricing
Free estimates for structural repairs and new installations. Flat diagnostic fee for opener and electronic troubleshooting.
| Service Type | Fee |
|---|---|
| New gate, fence, or opener installation estimate | Free |
| Structural repair — hinges, welds, frame, post, misalignment | Free estimate |
| Gate opener / electronic diagnostic | $175 |
| Simple reset, limit adjustment, or minor correction — no parts | $175 covers it |
| Repair quote approved — diagnostic credited to total | $175 applied |
| Repair quote declined | $175 due |
| Commercial / HOA / apartment opener diagnostic | $250 |
| After-hours / emergency response | $250+ |
The clean offer: Free estimates for new installs and structural repairs. $175 diagnostic for opener and electronic troubleshooting — credited toward your repair if you approve the work. No surprise charges. Written quote before we touch anything. All work done in-house.
Swing Gate Repair Houston TX — Hinges, Posts & Operators — Frequently Asked Questions
Why is my swing gate sagging?
A sagging swing gate almost always has a worn hinge or a shifted hinge post. As the greaseable ball-bearing barrel hinge wears or the post leans in Houston's clay, the latch end drops, the gate drags, and the latch stops catching. We weld in a new heavy-duty hinge and re-plumb the post — a permanent structural fix, not a shim.
My dual swing gates don't meet in the middle — why?
Misaligned dual swing gates usually have one leaf sagging from a worn hinge or shifted post, or the two operators out of sync on timing and limits. We level both leaves structurally first, then resynchronize the operators so they meet cleanly in the center.
Can you fix a swing gate hinge without replacing the gate?
Yes. We cut out the worn or seized hinge and weld in a new heavy-duty greaseable hinge, then re-square the gate. Because we weld in-house, we repair the hinge and structure rather than replacing the whole gate.
Why does my swing operator keep stalling?
Swing operators like the LA400 and LA500 stall and throw Code 93 when a sagging or post-shifted gate forces them past their load. The operator is protecting itself from the structural problem. We fix the hinge and post first, then recalibrate the operator.
How much does swing gate repair cost in Houston?
Structural hinge and post work is quoted with a free estimate. If a swing operator also needs diagnosis, that's $175 residential or $250 commercial, credited toward the repair. Written quote before any work.
Related Services
Gate Post Shifting Houston
Clay-soil post resets behind most sag.
Gate Welding Repair Houston
Hinge and structural welding.
LiftMaster LA400 Repair
The most common swing operator.
Slide Gate Repair Houston
For slide rather than swing gates.
Gate Opener Repair Houston
All operator brands.
Gate Repair Houston
Full-spectrum structural and electronic repair.
Swing Gate Sagging? Call Rampart Now.
Worn hinges, shifted posts, stalling operators — we fix the structure and the electronics.
In-house welding. Same-day service across Houston and Fort Bend.
(713) 816-5880"Promptly returned my text. Arrived on time and completed repairs to my satisfaction. Rampart is now my first call for gate and opener repair."
"Luis was quick to respond and work was done at a more affordable price than anywhere else we quoted. Patient and friendly. Will call them back!"
"Luis was prompt in providing an accurate estimate, ordered the necessary parts, and installed immediately. 5-star company!"