| All-O-Matic gate repair Houston |
All-O-Matic Slide Gate Operator Repair Houston TX
Rampart Welding repairs All-O-Matic slide and swing gate operators across Houston, including SL-45, SL-90, and SL-100FP models. We fix motors, control boards, limit assemblies, chains, and clutch adjustments on commercial and HOA gates, with priority same-day dispatch. Call (713) 816-5880.
All-O-Matic operators are common on Houston apartment, storage, and warehouse slide gates. When the gate runs and stops, won't close, or grinds under load, we diagnose the drive train and board — and check the gate itself before condemning the operator.
All-O-Matic Problems We Fix
Slide operator faults, residential and commercial.
- Gate runs then stops mid-travel
- Won't close or over-travels
- Worn clutch slipping under load
- Chain or sprocket worn / jumping
- Control board or limit fault
- Motor straining or overheating
Houston Conditions That Stress All-O-Matic Operators
High-Cycle Commercial Wear
Apartment and storage gates on All-O-Matic operators cycle far more than residential — wearing the clutch, chain, and sprocket faster than rated. Most All-O-Matic calls are mechanical wear, not electrical failure.
Clutch Slip Under Load
The All-O-Matic's mechanical clutch slips when it wears or when a dragging gate forces it past its setting. The motor runs but the gate barely moves. We adjust or replace the clutch and fix the underlying drag.
Board & Limit Faults
Heat and surge damage the control board, and vibration from high-cycle use drifts the limit settings. We test the board and recalibrate limits after confirming the drive train is sound.
Why Does My All-O-Matic Gate Run Then Stop?
An All-O-Matic that starts and stops is usually a limit-switch setting, a worn clutch, or a chain or sprocket binding under load. On high-cycle commercial gates these wear predictably. We adjust limits and inspect the drive train before replacing the control board.
A start-then-stop fault on a commercial slide gate is almost always mechanical resistance the operator can't overcome — a binding chain, a slipping clutch, or a gate dragging on its track. Replacing the board without fixing the resistance just sends the new board down the same path.
- Clutch inspected and adjusted or replaced
- Chain tension and sprocket wear checked
- Limit settings recalibrated
- Track and rollers checked for the drag forcing the stop
Diagnostic & Service Pricing
Free estimates for structural repairs and new installations. Flat diagnostic fee for opener and electronic troubleshooting.
Commercial All-O-Matic diagnostics are $250, credited toward the repair if approved. We carry common commercial slide-operator parts on the truck, so most calls are handled same-visit. Written quote before any work.
| Service Type | Fee |
|---|---|
| New gate, fence, or opener installation estimate | Free |
| Structural repair — hinges, welds, frame, post, misalignment | Free estimate |
| Gate opener / electronic diagnostic | $175 |
| Simple reset, limit adjustment, or minor correction — no parts | $175 covers it |
| Repair quote approved — diagnostic credited to total | $175 applied |
| Repair quote declined | $175 due |
| Commercial / HOA / apartment opener diagnostic | $250 |
| After-hours / emergency response | $250+ |
The clean offer: Free estimates for new installs and structural repairs. $175 diagnostic for opener and electronic troubleshooting — credited toward your repair if you approve the work. No surprise charges. Written quote before we touch anything. All work done in-house.
All-O-Matic Slide Gate Operator Repair Houston TX — Frequently Asked Questions
What All-O-Matic models do you repair?
We service the common All-O-Matic slide operators — SL-45, SL-90, and SL-100FP — plus their swing models, including motors, control boards, limit assemblies, chains, and clutch adjustments, on residential and commercial Houston gates.
Why does my All-O-Matic gate run then stop?
An All-O-Matic that starts and stops is usually a limit-switch setting, a worn clutch, or a chain or sprocket binding under load. On high-cycle commercial gates these wear predictably. We adjust limits and inspect the drive train before replacing the board.
Do you handle commercial All-O-Matic gates same-day?
Yes. All-O-Matic operators are common on Houston commercial properties, and stuck commercial gates get priority same-day dispatch. We carry common commercial parts on the truck. Call (713) 816-5880.
What does All-O-Matic repair cost in Houston?
Commercial diagnostics are $250, credited toward the repair if approved. We provide a written quote before any work and carry common parts for same-visit repair.
Related Services
Gate Opener Repair Houston
All operator brands diagnosed and repaired.
Slide Gate Repair Houston
V-tracks, rollers, chains, cantilever systems.
Commercial Gate Repair Houston
High-cycle apartment and warehouse gates.
Automatic Gate Repair Houston
Full automatic system diagnostics.
Access Control Houston
Loops, keypads, and entry integration.
Gate Maintenance Plans
Catch clutch and chain wear before failure.
All-O-Matic Down? Call Rampart Now.
Clutch slip, board faults, chain wear — we diagnose the full system.
Priority commercial dispatch across Houston and Fort Bend County.
(713) 816-5880"Promptly returned my text. Arrived on time and completed repairs to my satisfaction. Rampart is now my first call for gate and opener repair."
"Luis was quick to respond and work was done at a more affordable price than anywhere else we quoted. Patient and friendly. Will call them back!"
"Luis was prompt in providing an accurate estimate, ordered the necessary parts, and installed immediately. 5-star company!"